Fujikura Fusion Splicer

July 09, 2024 Post a Comment

Fujikura fusion splicer

At $60-120/hr, a fusion splice in a drop location will cost $30-$60 labor plus the splicing cost.

What are the 7 steps to do the fusion splice?

Steps of Fusion Splicing Fiber Optic Cables

Insert One Side of Fiber in the Splice Protective Sleeve.
Strip the Fibers' Buffer Coatings Accurately. ...
Clean the Fibers from Remaining Coating Particles. ...
Cleave the Ends of Fibers at Precisely 90° Angle. ...
Brace the Fibers in the Fusion Splicing Device.

What does a fusion splicer do?

Fusion splicers are used to create long cable lengths by splicing multiple cable segments. Although the splicer will give an estimate of the splice loss, the only way to test it is with an OTDR.

How long does it take to fusion splice fiber?

A general rule of thumb is that a single splice takes about four minutes, and a 12-fiber mass fusion splice takes about eight minutes per splice, respectively. Splicing a 1728-fiber count cable (144 mass splices) would take about 19 hours of steady splicing for a ribbon cable.

How much is the power loss of the fusion splice?

In fusion splicing, the acceptable loss is reduced to around 0.1 to 0.5 dB per splice.

Does a fusion splicer require calibration?

Calibration; It Needs to Be Done A fusion splicer that is out of calibration will produce inferior splices. False readings from an OTDR and a poor connector splice joining cable will cost you time and money.

How do I become a certified fiber splicer?

Requirements needed to become a Fiber Splicer Apprentice: Clean background and driver's license history. Mechanical experience in some form is a plus (auto, telecom, electrical, plumbing, military experience) Ability to travel up to 75% of the time.

Is fiber splicing hard?

The ends have to be cut perfectly straight and smooth, or it needs to be done over. Difficult to Install: it's not easy to splice fiber optic cable. And if you bend them too much, they will break.

Which method of splicing is better?

To summarize, fusion splicing is the preferred splicing method in today's fiber optic networks, due to the significantly improved splice performance over mechanical splicing.

Is fiber optic splicing a good career?

You can earn an annual average salary of $51,183 as a Fiber Optic Splicer. There is also a job growth rate of 4%, which is a good start. You also have the chance to further your career through the years when you start as a Fiber Optic Splicer.

How do you become a fusion splicer?

To become a fiber optic splicer, you typically need at least a high school diploma or GED certificate and relevant experience. However, fiber optic cabling is complex and uses light to transmit data, so splicers need special skills to manage and install the cabling.

What is the difference between mechanical and fusion splicing?

Fusion splicing can be performed as a single fusion (fusing just one fiber at a time) or as a mass fusion (fusing 12 fibers in a single operation). Mechanical splicing doesn't permanently join two fibers together; instead, it precisely “holds” them together, enabling light to pass from one fiber to the other.

How hot does a fusion splicer get?

An optical fiber fusion splicer is an apparatus that instantly connects two fibers placed left and right on the apparatus by fusing the end surfaces of the fibers at a high temperature (approximately 1,800°C) created by arcing (Fig. 1).

In what environment would you not use a fusion splicer?

Fusion splicers use an electric arc to fuse the fibers together so they should never be used in an environment where flammable gases or liquids are present. Never look into the end of a live fiber connector.

Can you splice fiber in cold weather?

Although the fusion splicing machine can work at temperature between -10ºC and +5ºC and the closure can be installed at temperature between -1ºC and +45ºC, you still need to ensure that the splicing technician work in the optimum conditions to give the maximum efficiency.

Which fiber optic system is better?

Although single-mode optical fiber holds advantages in terms of bandwidth and reach for longer distances, multimode optical fiber easily supports most distances required for enterprise and data center networks, at a cost significantly less than single-mode.

What is a good dB loss for fiber?

For singlemode fiber, the loss is about 0.5 dB per km for 1310 nm sources, 0.4 dB per km for 1550 nm.

What is a good fiber dB reading?

Fiber end with flat cleave: -14 dB. Good multimode PC connection: -35 dB or lower. Good singlemode PC connection: -50 dB or lower. Good angle-polish connection: -60 dB or lower.

How many points should you calibrate?

A minimum of three calibration points are necessary to prove linearity and accuracy.

How often should a tool be calibrated?

As a general rule of thumb, it's wise to test the calibration of your torque tools every six months or twelve months. That's rare enough that it doesn't impede productivity and often enough that it doesn't create obscene liabilities.